Kiiroo PowerBlow definitely not worth it.

Reeses

Heads up, the powerblow by kiiroo for the Keon sleeves BLOWS... in a bad way...

So right off the bat, noticed this thing doesn't have a 1way pressure release valve, so when you get it all set up, get hard, get lubed, you're super excited to watch Charlotte Sartre suck out every drop... dun dun dun.... You can't slide into the damn thing...

Tried a tad more lube, tried to force my way in.... which is very very uncomfortable... and noticed air was being forced out of every part of the thing that it could escape, except the powerblow...

The sleeve and case had become pressurized!!! 🤬

To get yourself inside you have to unscrew the powerblow, enter fully, then screw the powerblow back on. Alright, now let's give it a shot, hook up a video of Sasha Foxxx on feel connect cause the hapticsconnect app doesn't recognize the device, and press play.

Yeah OK it sucks on you a little bit, a LITTLE BIT.
Not at all enough to get off though... now, try to stoke yourself or with the Keon, the vacuum is too intense to slide out even 1/4 of your shaft, if you or your Keon forces past that it "burps" and breaks vacuum, now next time you or Keon goes to stroke in again, BAM it's pressurized and you can't get back in.

The sleeve was literally not moving up and down me at all, but the outsides of the Keon was pushing away from me.

Total total let down, and could have been prevented by a 1 way pressure relief valve and maybe a 10"Hg differential check valve, I have no idea how this thing got past engineering, quality control, and focus/test groups etc.

RealcumberScripts

Reeses thanks for reporting your experience, that's strange because my experience with it was very good, seemingly the opposite of yours
Definitely would be curious to know which sleeve you used - did you use the specific power blow Victoria Mouth sleeve (with the wider opening)?

I didn't actually have any of those issues, in fact the suction kept me inside the Keon, and I slipped out less because of the suction

I've never had sufficient suction previously with any of those toys with the release valves , so the suction on the power blow was notably strong at least on my unit

Did you use the rubber ring at the end cap, as well as the curved insert at the mouth end of the case?

doublevr

Reeses oh wow, didn't see this coming

CanOTuna

I had been interested in this but was waiting for someone's word on how well it actually works. Just to make sure, were you using one of the "compatible" sleeves that they have listed on the website or a previous one?

Sorry you had a bad experience but thanks for the warning.

Reeses

RealcumberScripts
I used the PowerBlow+FeelKayley kit, then rolled through all my other Keon sleeves.

Yup, I used the o-ring on the end and the collar that goes under the locking ring, and tried it later without the collar under the locking ring.

It really was like trying to push the plunger on a syringe with a cap on the syringe while entering. Thing really needs a positive pressure relief valve for entering.

Of course I emailed Kiiroo almost immediately, I have a 0-psi check valve laying round, but I shouldn't have to drill and glue the sleeve case when this "sucker" cost almost a $100, also shouldn't have to unscrew the powerblow everything I want to enter the sleeve IMO.

RealcumberScripts

Reeses thanks for letting us know - I haven't yet tried the Kayla or Tanya power sleeves, but I'm wondering those are not ideal shaped sleeves, and that maybe the Feel Victoria Mouth is more optimal with the power blow (which is what I used)

My guess is that the power blow (or any suction device) works much better accepting re-entry with wider opening sleeves (like the Feel Victoria Mouth sleeve has)

Most sleeves that Kiiroo offers are actually tighter/firmer than most fleshlights I've found (opening and inside canals)

Tighter sleeves are more potentially problematic for automatic strokers in general, with or without suction - I always recommend a looser/wider sleeve, and have recommended it for upcoming SLR Toy's sleeves

Maybe give it another try instead with a wider/looser fleshlight sleeve you may have laying around?

Reeses

RealcumberScripts
Yeah man I noticed the same thing with kiiroo sleeves, they're definitely tighter than the majority of FL sleeves, and like you say it's a denser TPE so that promotes issues even compaired to a tight FL sleeve that is more supple.

And YUP, I did try the vic june mouth, same issue. I modded a cap with a 0-psi check a while back for Keon cases, so you can enter but vacuum is applied out the out stroke, and that little $3 mod blows the PowerBlow out of the water, sadly.

Reeses

Update:

Okay, figured some stuff out. I covered the powerblow with my hand, not installed on the sleeve case, and powered it up. Mine has a hellacious vacuum leak around the seam under the charge port and up/down buttons.

Tightly covered that seam with electrical tape and checked it out.

Now it'll actually suck me into the sleev, a few times at least then it sounds loaded up constantly.
Pulled the powerblow off and inspected the situation, the sleeve gets pushed out of the case some when I enter fully, so trimmed the sleeve up some with a pair of scissors, and tried again.

Now we're in business! Tried it with the Keon running on a different phone and gotta say, if I could hook both the Keon and the powerblow up to hapticsconnect, this would be pretty kickass.

As it sits I was running the Keon off hapticsconnect on my daily phone, and powerblow off a spare phone using feel connect on some generic video.

Granted, still poor quality control, covered I'm electrical tape means no charging, or up or down buttons. And let's be honest, electrical tape turns into a huge sticky mess after like a day.

RealcumberScripts

Reeses thanks for the followup! Fortunately I dont need to use any additional tape on my unit, but thats good to know what further helped in your case! (wondering if you received a leaky seal defective unit?)

Really hoping we can get power blow synchronized support soon, I can imagine it being quite nice as well synced up to our content 🙂

Reeses

RealcumberScripts

RealcumberScripts
Oh yeah, definitely a defective seal or gasket in the case, I'm hoping kiiroo will make an exception to their "not if the box is opened" policy and exchange the unit.

DEFINITELY would be neat sync'd to the app, almost seems like some tweeking on how it reads the script would be needed. If it's being ran in conjunction with a Keon, the powerblow almost needs to start applying vac 20-30ms before the Keon goes to extend, as the unit seems to take time to load up.

raser1

Hey Reeses, I've made a post here about Powerblow support coming soon:
https://forum.sexlikereal.com/d/5752-powerblow-by-kiiroo

Let us know if you have any suggestions.

hundercover

I've just received my Powerblow and am facing the same issue - entering is hard, and moving is near-impossible and causes a "burp" even on the lowest suction strength.

Have I received a defective unit, or am I doing something wrong? I don't have any vacuum leaks as far as I can tell.

raser1

hundercover Hey it sounds like the seal/vacuum is too strong actually. That seems to be a more common issue. Maybe you can try using it without the extra insert in the case.

hundercover

raser1 Thanks! I've found that using a looser sleeve (Britney instead of Tanya) solves this problem also.